Korg from hell…

Recently had a Korg MS20 to look at that was exhibiting some very odd behaviour. Generally the tuning was a bit off and there was some residual LFO modulation of the VCOs even when all modulation controls were at minimum. Odd as the measured keyboard voltage looked OK. Took the synth apart (the MS20 is not that easy as all the pots have to be un-done just to get at the board) and it was found that the faults changed if the internal looms were moved about – even stranger.

Usual suspects checked (power supply voltages etc.) and everything seemed OK. Time to check with an oscilloscope and bingo – several volts of parasitic oscillation at a frequency well above audio all over the ground plane. This was going to be tough as there are a large number of culprits (op-amps) on the main board. Started at the main regulator and hunted for the IC where the maximum oscillation and tracked it down to the buffer for the keyboard divider.

Changed IC and – no change!

Hmmm, that’s odd. Back to circuit diagram and no supply decoupling around offending IC (actually very few anywhere) so time to strap a couple of 22n capacitors close to the IC across the rails and hooray – no more oscillation.

The 22n capacitors needed to restore normality...
the 22n capacitors needed to restore normality

Calibration of keyboard voltages went back to exactly the right values, oscillators were re-calibrated and were accurate within a cent across the entire keyboard, re-calibrated everything back to the original Korg spec and the whole synth went back to sounding really good.

MS20 should have done Glastonbury by the time you read this – another satisfied customer…

Hardware every time…

Recently been fixing an ARP sequencer which arrived in a non-working state. After some time with an oscilloscope and a couple of replacement parts normality was restored.

So while testing I pondered the artistic use of  such a beast, surely with a maximum of 16 notes it must be very limiting. However I came up with a way of using it that seemed to give endless variations but with the chance to determine how things go so it is not a totally random sequence.

Here goes with the explanation, hope you follow it…

First set up a number of notes that have a reasonable musical relationship but make sure that you program in more than one occurence of the notes you want to hear most often. Say 3 of one, 2 of another, 2 of another and one of a note you only want occasionally.

You then run the sequencer in random order mode and you will get a constantly changing stream of notes whose probability of occuring is determined by the number of duplicates you have put in, more duplicates ensures that the note is heard more often. The final sneaky bit is to use the skip function and that allows adjustment of the probability of the occurence of a note being played on the fly.

To complete this I used the other 8 trigger bus switches to determine if a gate was sent allowing notes to be made into rests.

If the 8 seed notes are also put in a meaningful order you can flip back to sequential mode giving a repeating motif that you can latch on to within the more semi-random stuff.

Try doing that on a computer!

This has inspired me to start work on a more modern version of a hardware sequencer, watch this space…

Tough Call…

Recently had to fully test and evaluate an rare old modular synth. Splendid , I thought, a chance to try out another interesting old synth that I hadn’t seen before. Got to the current resting place to find it was an old PPG analogue modular that appeared to be a fair copy of and old Moog modular. Here’s the tough bit, all the controls were labeled in German!

Everything…

Started off by identifying the oscillators (only three – shame). Then had a brainwave, step back until the writing couldn’t be read and bingo everything became recognisable. Reason – it was such a good copy of a modular Moog that the knob layouts started to look familiar so various modules could be identified. From that observation I worked out the EIN and AUS were the inputs and outputs so with a fistful of patch cables the old beast was soon making some great sounds.

One major difference (improvement) was that most module had several control voltage inputs.

The sequencer was such a close copy of a Moog that I ended up operating it without reading anything. But all in all a very nice machine with a very classy filter, capable of some very nice sounds.

Did you say Silent Piano. Have marketing lost the plot…

One of the strangest thing I’ve looked at recently is a Yamaha Silent Piano. On paper it sounds a bit weird but here is the idea.

Take a perfectly good upright piano (actually a very good one) and then add a digital piano as well. The clever bit is that you can mechanically disable the normal piano so that the hammers do not strike the strings but a series of optical sensors under the keys still determine which notes have been played. You then plug in a pair of stereo headphones and practice away without disturbing anyone – genius…

As a bit of a nerd I was quite impressed by the optical detector system that determines which notes have been played and at what velocity. This is done by two beams per key (2 x 88). As a wired system would need two wires per beam this has been reduced by using optical fibres. This allows multiple beams to be derived from a single transmitter and that multiple beams can be received by a single receiver, thus reducing the electronics. The whole lot is arranged as a matrix that is being scanned at regular intervals fast enough to be able determine which of the keys have been pressed.

As each key has to cut two beams then it is possible to calculate the speed the key is travelling by measuring the time taken between the beams being cut. On the one I looked at there was a small brass vane on the bottom of each key positioned so it cuts both beams.

The bit that got me was that with headphones on and the piano in silent mode the brain links the clunk of the disabled hammer with the sound in the phones and projects the sound “into” the piano making the experience of playing very realistic indeed.

Ones that got away…

You must have done it – sell something that you think is redundant and then years later regret it, I know I have…

Leaving the USA hard-tail Strat aside (as this isn’t a guitar related blog thingy), the one I really regret selling was an Oberheim OB-1 number 00036.

The OB-1 was the first commercially produced monophonic synth with memories. Only eight, but that was eight more than anyone else! A truly stunning feat as there was no microprocessor in there it was all done with discrete digital logic. Same principle as later programmables such as the Prophet V, scan all the pots in quick succession, digitise the voltages on each and store the values in RAM. Use a synth voice where every parameter is voltage controlled and derive all these voltages from the previously stored values to be able to recall sounds at will.

However it isn’t the programability that I now miss, it is the truly glorious sound of a synth with the smooth Oberheim filter that is quite different to the MiniMoog that replaced it.

Ho hum…

PS: Finally resolved this problem by getting a “modern” Oberheim 2 voice. Still not programmable but the bonus of having two of those lovely filters and a very capable MIDI sequencer as well…

Do the old ones really sound better?

Had a reminder recently that some instruments deserve the reputation that they have. I was asked to sort out a very unwell set of Moog Taurus Pedals (the original version).

A freshly revived set of Mk1 Taurus Pedals
Freshly revived Taurus Pedals

I approached the task with a “whats all the fuss about” especially when the instrument was powered up and a very sick weedy sound was the result. A bit of investigation traced the fault to the power supply where the rail for the discrete logic would measure 5V under no load conditions but collapse when everything was connected up.

Regulator duly replaced the pedals were powered up and the result was a deep deep trouser-flapping bass that makes even a Mini-Moog sound a bit thin. How do they do that…

Note that MoogMusic (www.moogmusic.com) are advertising that they are going to do a re-issue, that should be interesting

Progress

Well most of the info from “members.aol.com/tronpage” is now available again, next job is to make sure that the search engines can find it. Meanwhile nothing else exiting to report on the synth front as most of the recent repairs have been amplifiers. Must have a rummage through my archives to find some interesting synth related stuff.

Oh and Happy New Year if you’ve got this far…

Mellotrons, Synths and electronics in music